MISUMI PSFCJ15-[25-1000/1]

L Dimension Tolerance; Circularity; Straightness; Perpendicularity; Concentricity and Changes in Hardness >> P.111 Annealing may lower hardness at shaft end machined areas (effective thread length + approx. 10mm). Shafts may have centering holes at end faces depending on shapes.

Type	D Tol.	Material	Hardness	Surface Treatment
Solid	One End Tapped	One End Stepped and Tapped	One End Threaded	One End Threaded with O.D. same as Shaft O.D.
PSFCJ	PSFCT	PSFCG	PSFCN	PSFCQ	g6	EN 1.3505 Equiv.	Effective Hardened Depth of Induction Hardening >> P.112 58HRC~	Electroless Nickel Plating

Specifications

Part Number	-	L	-	F	-	B	-	P	-	M
PSFCJ20	-	75
PSFCT20	-	525							-	M8
PSFCG20	-	400	-	F25			-	P16	-	M10
PSFCN20	-	950	-	F50	-	B30	-	P10
PSFCQ12	-	500			-	B20

Solid Type; One End Tapped Type; One End Stepped and Tapped Type

Part Number	1mm Increment	Selection	(Y)Max.	R	C
Type	D	L (Solid / One End Tapped)	L (One End Stepped and Tapped)	F	P	M (One End Tapped)	M (One End Stepped and Tapped)
Solid Type PSFCJ One End Tapped PSFCT One End Stepped and Tapped PSFCG	8	20~ 800	25~798	2≤F≤Px4	6	3	4	5									3											800	0.3 or Less	0.5 or Less
10	20~ 800	25~798	6~ 8	3	4	5	6								3	4	5									800
12	20~1000	25~998	6~10		4	5	6	8							3	4	5	6								1000
15	25~1000	25~998	6~13		4	5	6	8	10						3	4	5	6	8	10						1000
20	30~1000	25~998	6~17		4	5	6	8	10	12						4	5	6	8	10	12					1000	1.0 or Less
25	35~1000	25~998	8~22		4	5	6	8	10	12	16					4	5	6	8	10	12	16				1000
30	35~1000	25~998	9~27				6	8	10	12	16	20					5	6	8	10	12	16	20			1000
35	35~1000	25~998	9~32					8	10	12	16	20	24				5	6	8	10	12	16	20	24		1000	0.5 or Less
40	50~1000	25~998	11~37						10	12	16	20	24	30				6	8	10	12	16	20	24	30	1000
50	65~1000	25~998	11~47							12	16	20	24	30				6	8	10	12	16	20	24	30	1000

• One End Tapped Type When Mx2.5+4≥L; tap pilot holes may go through. • One End Stepped and Tapped P≥M+3 When Mx2.5+4≥Y; tap pilot holes may go through. One End Threaded

Part Number	1mm Increment	P Selection	(Y)Max.	R	C
Type	D	L	F	B
One End Threaded PSFCN	8	25~798	2≤F≤Px5	(When P≤6) B≤F-2 (When P=8; 10) B≤F-3 (P≥12) B≤F-5 B≥Pitchx3	3	4	5	6								800	0.3 or Less	0.5 or Less
10	25~798		4	5	6	8							800
12	25~998			5	6	8	10						1000
15	25~998			5	6	8	10	12					1000	1.0 or Less
20	25~998				6	8	10	12	16				1000
25	25~998					8	10	12	16	20	24		1000
30	25~998					8	10	12	16	20	24		1000
35	25~998						10	12	16	20	24	30	1000	0.5 or Less
40	25~998							12	16	20	24	30	1000
50	25~998								16	20	24	30	1000

Coarse Thread Dimension
M	Pitch
3	0.5
4	0.7
5	0.8
6	1.0
8	1.25
10	1.5
12	1.75
16	2.0
20	2.5
24	3.0
30	3.5

One End Threaded with O.D. same as Shaft O.D.

Part Number	1mm Increment	M	(Y)Max.	R	C
Type	D	L	B
One End Threaded with O.D. same as Shaft O.D. PSFCQ	8	25~793	7~40	8	800	0.3 or Less	0.5 or Less
10	25~795	8~50	10	800
12	25~991	9~60	12	1000
20	25~987	13~100	20	1000	1.0 or Less
30	25~982	18~150	30	1000

For shafts with O.D. same as Shaft O.D.; L dimension has priority; thus the effective thread length will be B-(Pitchx2). Alterations