MISUMI SETRS6-[8-50/0.5]-SC[0-42/1]

Type	Material	Surface Treatment
L Dimension Selectable	L Dimension Configurable
Standard	Wrench Flats	Thread Dia. Configurable	Thread Dia. Configurable, Wrench Flats
-	NETRF	NETRS	NETF	NETS	*EN 1.0038 Equiv.	-
ETKR	ETKRF	ETKRS	ETKF	ETKS	Black Oxide
PETR	PETRF	PETRS	PETF	PETS	Electroless Nickel Plating
-	BETRF	BETRS	-	BETS	Trivalent Chromate (Black)
SETR	SETRF	SETRS	SETF	SETS	EN 1.4301 Equiv.	-
-	AETRF	AETRS	AETTF	AETTS	EN AW-2017 Equiv.	Clear Anodize

*C0.2~0.5 at the corner *For L dimension selectable products, steel for general structure is used. Specifications

Part Number	-	L	-	SC	-	M	-	N
ETKR10 ETKRF10 ETKF20 SETS25	- - - -	150 150 400 500	-	SC100	- -	M8 M10	- -	N10 N12

L Dimension Selectable

Part Number	L Selection	M (Coarse)	S	W	1
Type	D
General Structural Steel ETKR PETR EN 1.4301 Equiv. SETR	6	15	20	25	30	35	40	45	50												3	3.5	5	8
8		20	25	30	35	40	45	50	60	70	80	90	100	110	120	130	140	150		4	6	7
10		20	25	30	35	40	45	50	60	70	80	90	100	110	120	130	140	150	200	5	6	8
12			25	30	35	40	45	50	60	70	80	90	100	110	120	130	140	150	200	6	7.5	10	10
15					35	40	45	50	60	70	80	90	100	110	120	130	140	150	200	8	10	13
20						40	45	50	60	70	80	90	100	110	120	130	140	150	200	10	15	17

L Dimension Configurable / L Dimension Configurable, Wrench Flats

Part Number	L 0.5mm Increment	SC 1 mm Increment With Wrench Flats Only	M (Coarse)	W	1
Type	D
L Dimension Configurable EN 1.0038 Equiv. NETRF ETKRF PETRF BETRF EN 1.4301 Equiv. SETRF EN AW-2017 Equiv. AETRF	L Dimension Configurable, Wrench Flats EN 1.0038 Equiv. NETRS ETKRS PETRS BETRS EN 1.4301 Equiv. SETRS EN AW-2017 Equiv. AETRS	*1 5	8~50	0~42	2.6	4	8
6	8~50	0~42	3	5
8	10~150	0~142	4	7
10	15~350	0~342	5	8
12	25~400	0~390	6	10	10
15	25~500	0~490	8	13
20	30~500	0~490	10	17
25	40~600	0~590	12	22
30	50~700	0~685	16	27	15
*2 35	50~800	0~785	16	30
*2 40	60~900	0~880	20	36	20
	*2 50	75~1000	0~980	24	41

*1. D=5 is not available for EN AW-2017 Equiv. material. When L≤Mx4, tapped hole goes through. When L≤(Mx2+5)+(Nx2+5), the pilot hole may go through. *2. D≥35 is applicable only to N , E and P . Thread Diameter Configurable / Thread Diameter Configurable, Wrench Flats

Part Number	L 0.5mm Increment	SC 1 mm Increment With Wrench Flats Only	M / N (Coarse) Selection	W	1
Type	D
Thread Dia. Configurable EN 1.0038 Equiv. NETF ETKF PETF EN 1.4301 Equiv. SETF EN AW-2017 Equiv. AETTF	Thread Dia. Configurable, Wrench Flats EN 1.0038 Equiv. NETS ETKS PETS BETS EN 1.4301 Equiv. SETS EN AW-2017 Equiv. AETTS	*1 5	15~50	0~42	2.6	3										4	8
6	15~50	0~42		3	4									5
8	15~150	0~142		3	4	5								7
10	20~350	0~342			4	5	6							8
12	25~400	0~390				5	6	8						10	10
15	30~500	0~490					6	8	10					13
20	40~500	0~490					6	8	10	12				17
25	50~600	0~590					6	8	10	12	16			22
30	60~700	0~685					6	8	10	12	16	20		27	15
*2 35	75~800	0~785						8	10	12	16	20	24	30	15
*2 40	75~900	0~880							10	12	16	20	24	36	20
	*2 50	75~1000	0~980								12	16	20	24	41	20

*1. D=5 is not available for EN AW-2017 Equiv. material. L≥Mx2+Nx2 When SC≤Mx3, W-M≥2 is needed. When L-SC≤Nx3, W-N≥2 is needed. *2. D≥35 is applicable only to N , E and P . L Dimension Tolerance L 8~ 300   0.1 L300.5~ 600 0.3 L600.5~1000 0.4 However, when L≤200, and when order volume at one time is less than 10 pcs., since the processing is done simultaneously, the difference of L dimension is within 0.02. Except L Dimension Selectable Alterations